Free Tool
Freight Class Calculator: Density to NMFC Class
Enter the dimensions, weight and number of handling units to get cubic feet, density in pounds per cubic foot, and the estimated class on the current NMFC density scale.
Book a DemoHow do you calculate freight class?
Multiply the length, width and height of each handling unit in inches and divide by 1,728 to get cubic feet. Divide the total weight in pounds by the total cubic feet to get density. Then find that density on the NMFC 13-tier scale: for example, 8 to under 10 lb per cubic foot is class 100.
Calculator
Enter one handling unit
Measure the pallet, crate or carton at its longest, widest and highest points, including any overhang. If you have several identical units, set the count.
Formula used
- Cubic feet = L × W × H in inches ÷ 1,728 × handling units
- Density = total weight in lb ÷ total cubic feet
- Class = the band the density falls in on the NMFC 13-tier density scale
Results
Enter dimensions and weight, then select “Estimate freight class”.
NMFC density scale: density to freight class
The 13-tier scale the NMFTA adopted in Docket 2025-1, in effect since 19 July 2025. Density is in pounds per cubic foot (lb/ft³).
| Density (lb/ft³) | Class |
|---|---|
| Less than 1 | 400 |
| 1 but less than 2 | 300 |
| 2 but less than 4 | 250 |
| 4 but less than 6 | 175 |
| 6 but less than 8 | 125 |
| 8 but less than 10 | 100 |
| 10 but less than 12 | 92.5 |
| 12 but less than 15 | 85 |
| 15 but less than 22.5 | 70 |
| 22.5 but less than 30 | 65 |
| 30 but less than 35 | 60 |
| 35 but less than 50 | 55 |
| 50 or more | 50 |
How to use it
Freight density and class, worked through
The calculator works in inches and pounds, the units the NMFC density scale uses, and converts centimetres and kilograms if you enter those. It applies the 13-tier scale that took effect on 19 July 2025 under NMFTA Docket 2025-1.
A worked example
A pallet measures 48 × 40 × 48 in including the pallet and weighs 500 lb. Its volume is 48 × 40 × 48 = 92,160 cubic inches, and 92,160 ÷ 1,728 = 53.33 cubic feet.
Density is 500 ÷ 53.33 = 9.38 lb per cubic foot, which falls in the 8 to under 10 band, so the estimated class is 100. If the same pallet weighed 600 lb, density would be 11.25 and the class would drop to 92.5.
How to read your result
The band in the table above is highlighted once you see your result. If your density sits just under a break point, a small change can move you down a class: a slightly lower stack height on the same weight raises density. Classes are cheaper as the number falls, so denser loads usually cost less per hundred pounds.
Common mistakes
Measuring the cartons but not the pallet. Ignoring overhang, which carriers measure. Rounding dimensions down. Using an old class from a previous bill of lading after the 2025 changes. And assuming every commodity is classed by density: items with their own NMFC entry may rate differently.
What to do next
Use the pallet calculator to test a lower stack height or a different carton pattern, then come back to check the class. For ocean or air legs, the CBM calculator gives cubic metres and chargeable weight.
Why it is an estimate
Density is one of four classification factors
The NMFC rates freight on density, handling, stowability and liability. Since Docket 2025-1 most commodities are classed by density alone, but items that are fragile, hard to load, hazardous or high in value can keep their own class or their own density sub-provisions. The class shown here is what the general density scale gives; your commodity's NMFC item and your carrier's tariff decide the class that is billed.
Freight class sets the rate, but how often you ship sets the bill. Planning orders from a demand forecast lets you build fuller, denser loads. See Perimattic Demand OS for SKU-level forecasting, the safety stock calculator and EOQ calculator for order timing and size, and the lead time calculator for transit planning. Teams that want freight rules built into their own systems can look at supply chain software development, and the free ERPStack purchase order generator covers the paperwork side of an order.
Density scale checked on 17 November 2026 against the 13-subprovision scale (NMFC item 35850) published by the National Motor Freight Traffic Association under Docket 2025-1, effective 19 July 2025. Later dockets, such as 2026-1, have moved more commodity groups onto it.
More shipping and inventory tools
Pallet Calculator
Find how many cartons fit on a pallet, the load height and weight, and pallets per trailer or container.
Learn moreCBM Calculator
Work out cubic metres, air and sea chargeable weight, and how full a 20 ft or 40 ft container would be.
Learn moreSafety Stock Calculator
Calculate optimal buffer stock using demand and lead time variability with Z-score tables.
Learn moreLead Time Calculator
Add up supplier, production and transit time to see the full order-to-delivery lead time.
Learn moreUniversal EOQ Calculator
Order quantity calculator on the Perimattic tools site, for comparing order sizes across items.
Learn moreSupply Chain Software Development
Custom software for shipment planning, freight data and supplier collaboration, built by Perimattic.
Learn moreFrequently Asked Questions
Freight class and density, answered
What is freight class?+
How do I calculate freight density?+
What changed in the NMFC density scale in 2025?+
Is freight class based only on density?+
Does the pallet count toward freight class?+
What happens if I get the freight class wrong?+
Ship from a plan, not a scramble
- Free consultation
- No commitment
- Tailored to your team